International Harvester / Farmall Super MVTA Parts

[Categories]   [All Farmall Models]   [Print]  

Drive Train
Bull Pinion Shaft Bearing Retainer Oil Seal - This bull pinion shaft bearing retainer oil seal has a 2.25 inch Inside Diameter, a 3.256 inch Outside Diameter and is .375 inch wide. There are two used per tractor. It Fits: 400, 450, 560, 660, MTA, Super M, Super MD, Super MDTA, Super MDV, Super MDV-TA, Super MTA, Super MVTA, Super W6, Super WD6, W400, W450, W6TA, M (SN: 294226 and up), MV (SN: 294226 and up), MD, MDV. Two needed per tractor. Replaces: 1699480C91, 200721H1, 3139744R1, 336626R91, 357037R91, 358896R91 (Item #: 163584, Ref: VT3755) $19.80
Gear Shift Boot - Some of the Farmall / International tractors were not factory equipped with a gear shift boot, and it was sold as an extra. This boot is used on models: H, M, 560, I4, I6, ID6, Super MVTA, 2606, HV, MD, T340, T5, MDV, MV, TD6, O4, O6, ODS6, OS4, OS6, Super H, Super HV, Super M, Super MD, Super MDV, Super MTA, Super MTA, Super MV, Super W4, Super W6, Super WD6, W4, W6, WD6, 300, 330, 340, 350, 400, 404, 424, 444, 450, 460, 504, 606, 660, B275, 354, 384. It measures 4-3/4 inches tall, 11/16 inch top hole inside diameter and 2-3/4 inches bottom hole. (Item #: 182890, Ref: 64603DA) $24.80
Reverse Idler Gear Bushing - This Bushing Measures 1.245 inches inside diameter, 1.375 inches outside diameter, 1.486 inches long. Sold individually. This bushing has a superior dimpled brass inner design to retain grease. No need for an external grease hole. Note: Must be honed or reamed to size when installed. Used on the following as a reverse idler gear bushing: 400, 450, 560, 660, B-450, BM, BMD, M, MD, MDV, MTA, MV, O6, ODS6, SBM, SBMD, Super M, Super MDTA, Super MDV, Super MDV-TA, Super MTA, Super MV, Super MVTA, Super W6, Super WD6, W400, W450, W6, W6TA, WD6, WD6TA; Replaces: 48841D (Item #: 109669, Ref: 48841D) $13.70

Electrical System
Distributor Drive Housing - This is a new distributor drive housing with an opening for tachometer drive. It is used to change from a magneto to a distributor or to add a tachometer drive to your tractor. The tachometer drive parts (tachometer drive assembly part number 369695R1, tachometer cable connector housing, part number 369692R1 and 363817R1, connection housing plate) or tach. Drive blockoff plate are sold separately. NOTE: Will also work on tractors without tach drive by ordering number 363764R1 block off plate. Use with 107304C91 distributor when replacing a magneto. fits tractor models A, A1, AV, AV-1, B, BN, C, Cub, Cub Lo-Boy, H, HV, I4, I6, I9, M, MTA, MV, O4, O6, OS4, OS6, Super A, Super AV, Super C, Super H, Super HV, Super M, Super MTA, Super MV, Super MVTA, Super W4, Super W6, Super W9, W4, W6, W6TA, WR9S, 100, 130, 140, 154, 184, 185, 200, 230, 240, 2404, 2424, 2444, 2504, 300, 330, 340, 3444, 350, 3514, 404, 424, 444, 504, 400, 600, 650 450. Replaces: 363749R91, 363763R11. (Item #: 178938, Ref: 363749R91) $107.00
Distributor Hold Down Clamp - For 5/16 inch hold down bolt and IH built distributor. 2 used per engine, sold individually. Fits fits tractor models A, AV, B, BN, C, Cub, Cub Lo-Boy, H, HV, Hydro 70, Hydro 86, I4, I6, I9, ID6, ID9, M, MV, O4, O6, OS4, OS6, Super A, Super A-1, Super AV, Super AV-1, Super C, Super H, Super HV, Super M, Super MTA, Super MV, Super MVTA, Super W4, Super W6, Super W6TA, Super W9, W4, W6, W9, WR9S, 100, 130, 140, 154, 184, 185, 200, 230, 240, 2400A, 2400B, 2404, 2405B, 2410B, 2412B, 2424, 2444, 2500A, 2500B, 2504, 2505B, 2510B, 2514B, 2544, 2606, 2656, 2706, 2756, 2806, 2826, 2856, 300, 330, 340, 350, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, 574, 600, 606, 650, 656, 660, 666, 674, 686, 706, 756, 766, 806, 826, 856. All with IH distributors. Replaces 341139R1, 353937R1. (Item #: 182464, Ref: 341139R1) $9.60
H4 Magneto Pinion Driven Gear - This gear has 24 teeth and measures: 0.380 inch inside diameter, 0.759 inch outside diameter, 1.075 inch gear outside diameter, 0.952 inch overall height. It is used on H4 Magnetos. (Item #: 183878, Ref: 49420DX) $24.40
Magneto Rotor H4 Magneto - This Rotor is used on tractors with H4 magneto. Replaces 47425DX, 47425DY, 47428DA (Item #: 111106, Ref: 47425DY) $11.80
Spark Plug Wire Set, Custom - IH or Delco Distributors and Magnetos. For the following models with 90 degree angle boots: A, I4, AV, Super A, Super A1, Super AV, SuperAV1, B, BN, C, Super C, Cub, Cub Lo-Boy, 154, 184, 185, H, HV, Super H, Super HV, M, MD, Super M, Super MD, Super MDV, MDV, Super MDVTA, MTA, Super MTA, MV, Super MV, Super MVTA, O4, O6, ODS6, OS4, OS6, T340, T5, T6, TD6, SuperW4, W4, Super W6, Super W6TA, W6, W6TA, Super WD6, WD6, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, W400, 404, 424, 444, 450, W450, 504. Replaces the following OEMS: 352947R91, 352951R91, 352954R91, 352956R91, 356687R92, 356689R92, 356691R91, 356694R92, 356695R92, 356697R93, 362439R91, 362789R91, 407487R1, 45327DA, 46277DA, 50075D, 52794D, 65352D, 65357D, 65358D, and 65359D. (Item #: 120100, Ref: S.67475) $17.50

Engine Gaskets
Crank Seal, Front - This front crankshaft oil seal has a 2.625 inch Inside Diameter, a 3.38 inch Outside Diameter and is .475 inch wide. It Fits: I6, I9, ID6, ID9, M, MD, MDV, MV, O6, ODS6, OS6, Super M, Super MD, Super MDTA, Super MDV, Super MDV-TA, Super MTA, Super MV, Super MVTA, Super W6, Super W6TA, Super W9, Super WD6, Super WD6TA, Super WD9, Super WDR9, T6, T6-61, T9, TD6, TD6-61, TD9, TD9-91, W400, W450, W6, W9, WR9, WR9S, 400, 450, 600, 650, B-450, BM, BMD, SBMD, Super BM. Replaces: 258511R91, 357972R91, 357977R91, 358511R91, 53872D, 410708 (Item #: 106640, Ref: 357972R1) $12.90

Engine Parts
No Picture Connecting Rod Bolt Lock Tab - .490 inch bolt hole diameter, 8 used per engine, sold individually. For tractor models (I6, M, MV, O6, OS6, Super M, Super MTA, Super MV, Super MVTA, Super W6, Super W6TA, T6-61, W6, 400, 450 gas, LP with C248, C264 and C281 engines 8 used), (WD9, WDR9 early diesels up to engine serial number 10265 16 used). (Item #: 167084, Ref: 47496DB) $6.90
Cylinder Head Stud - 1/2 inch x 7 1/16 inch. For gas and LP Models: I6, M, MTA, MV, O6, OS6, Super M, Super MTA, Super MV, Super MVTA, Super W6, Super W6TA, T6, U6, W6, 400, 450. (Item #: 178330, Ref: 49023DA) $19.20
Cylinder Head Stud - 1/2 inch x 6 7/8 inch. For gas and LP Models: I6, M, MTA, MV, O6, OS6, Super M, Super MTA, Super MV, Super MVTA, Super W6, Super W6TA, T6, U6, W6, 400, 450. (Item #: 178329, Ref: 46117D) $19.20
Governor Throttle Shaft Rebuild Kit - This Governor Throttle Shaft Rebuild Kit fits: H, HV, I4, I6, M, MV, O4, O6, OS4, OS6, Super H, Super HV, Super M, Super MTA, Super MV, Super MVTA, Super W4, Super W6, Super W6TA, T6, T6-61, U4, U6, W4, W6, 300, 350, 400, 450 all Gas and LP. Replaces: Cotter pin: 103361, Pin: 103494, Groove pin: 142952, Bushing: 45696D, Felt washer: 48493D, Lever: 6288D, Gasket: 48501D, 53877DB, 66272DA. Kit includes: lever, bushing, felt washer, (3) gaskets, groove pin, cotter pin, and pin. (Item #: 183906, Ref: IHS2559) $51.00

Fuel System / Air Intake
Air Cleaner Pipe - 2-1/4 inch outside diameter. For tractor models M, MV, Super M, Super MV, MTA, Super MV-TA, (Super W6 serial number 3951 and up), Super W6-TA, 400, 450, W400, W450 all gas or LP. Replaces 51441D. (Item #: 126383, Ref: 357028R1) $42.00
Sediment Bowl Gasket and Screen - This is a 2 Inch Outside Diameter Gasket and Screen. The Screen has a 3/8 Inch center hole. (Item #: 105364, Ref: 49923D) $3.50
Throttle Plate Assembly - This is a Square Tooth Throttle Control Assembly (Governor Control Assembly) used on H, HV, M, MTA, MV, Super H, Super HV, Super M, Super MTA, Super MV, Super MVTA. Replaces: Handle: 361244R11, Sector: 361246R11, Assembly: 366727R91 (Item #: 114409, Ref: 366727R91) $70.00
Throttle Plate Assembly - H, HV, M, MTA, MV, Super H, Super HV, Super M, Super MTA, Super MV, Super MVTA; Replaces: Saw tooth Lever: 51348DAX, Saw tooth sector: 51351DBX, 51351DBXA (Item #: 114409, Ref: 51351DBX) $70.00

Gaskets
Push Rod Side Cover Gasket - Replacing OEM part numbers 49029DA, 49029DB this gasket is used on Gas and LP models: M, I6, Super MVTA, MTA, MV6, OS6, Super M, Super MTA, Super MV, Super W6, Super W6TA, W6, 400, 450 (Item #: 154785, Ref: 49029DA) $18.00

Oil System
Oil Level Indicator - This oil level indicator is a replacement for the oil level petcock. Remove the original petcock and replace with this conversion. Has 3/8 inch NPT male fitting. Dipstick is 4.91 inches long. For models using the original oil petcock in A, AV, B, BN, C, F12, F14, F20, F30, H, HV, I12, I14, I4, I6, M, MTA, MV, O12, O14, O4, O6, OS4, Regular, Super A, Super A-1, Super AV, Super AV-1, Super C, Super H, Super HV, Super M, Super MTA, Super MV, Super MVTA, Super W4, Super W6, Super W6TA, W12, W14, W30, W4, W6, 10-20, 15-30, 22-36 and early models of 350, 400, W400, W450 used to replace top oil checking petcock. Originally used as an aftermarket product in the 1940's. (Item #: 1998TA-New) $46.50

PTO / Driveline
Live Planetary PTO Front Bearing Retainer Seal - This live planetary PTO front bearing retainer seal has a 1.5 inch Inside Diameter, a 2.38 inch Outside Diameter and is 0.315 inch wide. It Fits: MTA, Super MDTA, Super MDV-TA, Super MTA, Super MVTA, Super W6TA, Super WD6TA, 300, 330, 340, 350, 400, 450, 460, 560, 660. Replaces: 103330R91, 289198, 338590R91, 357973R91, 357978R91, 359056R91, 359449R91, 359789R91, 360437R91, 364470R91, 364474R91, 367162R91, 58685D, 70259D, 703281R91, 708095R91, 80093H, 93516R91, 953019R1, 953020R1 (Item #: 121742, Ref: AT344T) $12.00

Seats
Upper Bolster Shaft Horizontal Seal - This upper bolster shaft horizontal seal has a 1.5 inch Inside Diameter, a 2.38 inch Outside Diameter and is 0.315 inch wide. It Fits: B-450, BM, BMD, M, MD, MDV, MTA, MTAV, MV, Super M, Super MD, Super MDTA, Super MDV, Super MDV-TA, Super MTA, Super MV, Super MVTA, 400, 450. Replaces: 103330R91, 289198, 338590R91, 357973R91, 357978R91, 359056R91, 359449R91, 359789R91, 360437R91, 364470R91, 364474R91, 367162R91, 58685D, 70259D, 703281R91, 708095R91, 80093H, 93516R91, 953019R1, 953020R1 (Item #: 121742, Ref: AT344T) $12.00

Steering
Steering Shaft Cross and Bearing (U-Joint) - Tighten up your steering with a new Universal Joint. This part measures 2.305 inches across cap to cap, with a 0.968 inch cap diameter. Some models use more than one, sold individually. Some models used different sizes, verify measurements. Replaces OEM numbers 10P715, 1KAR758, 224890, 350254R91, 357439R91, 363313R91, 363321R91, 52977DAX, 70224890, 836514M91, 841193M92, A20435, A20684, A30408, A30425, A30428, A30435, VTA3227, Z862 (Item #: 115351, Ref: 70224890) $11.00
Steering Wheel Nut - This steering wheel nut fits the following tractor models: Cub Cadet 100, Cub Cadet 102, Cub Cadet 122, Cub Cadet 70, A, AV, AV1, B, BN, C, H, HV, I4, I6, I9, ID6, ID9, M, MD, MDV, MTA, MV, O4, O6, ODS6, OS4, OS6, Super A, Super A1, Super AV, Super AV1, Super C, Super H, Super HV, Super M, Super MD, Super MDV, Super MDVTA, Super MTA, Super MV, Super MVTA, Super W4, Super W6, Super W6TA, Super W9, Super WD6, Super WD6TA, Super WD9, Super WDR9, W4, W6, W9, WD6, WD9, WDR9, WR9, WR9S, 100, 130, 200, 230, 600, 650, Cub Lo-Boy, 300, 400, 450, and Cub. It measures 0.75 inches wide, 0.444 inches tall, and has a 16 NF thread size. Replaces part numbers: 114499, 122403, and 219753. (Item #: 157780, Ref: 353435X1) $1.00
Steering Worm Gear, Sector - 32 teeth. For tractor models 400, 450, M, Super M, Super MTA. The style of this gear is full circle. This gear has 32 teeth. It can also replace a 19 tooth sector (1/2 inch moon style). Replaces: 50037DA, 50037DB, 704168R1. (Item #: 124445, Ref: 50037DB) $160.00
Steering Worm Shaft - This Steering Worm Shaft is 46-1/2 inches overall length with 3/4 inch NF thread. This shaft will NOT fit diesels UNLESS customer lengthens the shaft. Fits: (M, MV gas, LP), (MTA, MTAV, Super M, Super MTA, Super MV, Super MVTA gas, LP; up to serial number F52627 or L512541), (400 LP only; with 22 inch tank; serial number 21804 and up without factory power steering), (450 LP only; with 22 inch tank; up to serial number 13135 without factory power steering). Replaces shaft: 50052DB and 50052D. (Item #: 151915, Ref: 50052D) $192.15
Steering Worm Shaft Bearing - This Steering Worm Shaft Bearing has a 0.984 inch inside diameter, a 2.047 inch outside diameter and a 0.590 inch width. Fits B, BM, BN, C, H, HV, M, MD, MDV, MTA, MV, Super C, Super H, Super HV, Super M, Super MD, Super MDV-TA, Super MTA, Super MV, Super MVTA, 200, 230, 400, 450, Super MTA, (424, 444 used as a steering worm shaft bearing; without power steering), 240, 300, 340, 350, 404, 504, 240, 404. Replaces: 1271857C91, 1273146C91, 210041, 43357D, 69696D, 741-0360, 741-3037, 941-3037, ST225, ST225AT, ST225B, ST225BT, ST225Y, ST678. (Item #: 178091, Ref: ST225B) $9.60
Steering Worm Shaft Oil Seal - This Steering Worm Shaft Oil Seal measures 1.000 inch inside diameter, 1.503 inch outside diameter, 0.250 inch wide. Fits B, BN, C, H, HV, M, MD, MDV, MV, Super C, Super H, Super HV, Super M, Super MD, Super MDV, Super MDV-TA, Super MV, Super MVTA, 200, 230, 240, 400, 450, MTA diesel, 300, 340, 350. Replaces: 359042R91, 359257R91, 364468R91, 43800D, 43800DA, 488561R91. (Item #: 122678, Ref: 43800D) $5.80
Universal Parts and Accessories Category: Accessories / Supplies

Accessories / Supplies
Auxiliary Heater, Universal - This universal auxiliary heater is used for tractor cabs, combines, backhoes, dozers, forklifts, etc. using 5/8 inch heater hose connections. Hot water forced air heat. Dimensions: 6-1/2 inches x 9-1/2 inches x 9 inches, steel powder coat housing with aluminum core. 3-speed high volume squirrel cage fan, 12-volt, 20, 000 BTU includes switch, brackets, instructions. (Item #: 182644, Ref: MIS3127) $385.00
Magnetic Block Heater - Universal. Magnetic utility heater. 120 volt AC, 200 Watts. Built-in thermostat maintains optimum temperature - will not exceed 250 degree F (121 degree C). Quick-grip handle protects hands from heat. 4-3/8 inches (11cm) length, 2-1/2 inches (6.3cm) width, 3 inches (7.5cm) height (including handle). (Item #: 178758, Ref: MBH1153) $97.00

Decals and Emblems
Decal, Fear This IH - Black and red, 12-1/2 x 3-3/4. For all Models. (Item #: 183484, Ref: S.67826) $15.80
Decal, IH Block - "IH" logo, 11 inches. (Item #: 183564, Ref: R4682) $17.40
Decal, IH Block - "IH", 3 inch x 3 1/4 inch Block. (Item #: 101094, Ref: R4681) $6.40
Decal, IH Block - "IH" logo, 1 3/4 inch. (Item #: 183266, Ref: R4680) $5.00
Decal, IH Block - "IH", 1 1/4 inch Logo . (Item #: 183058, Ref: R4679) $3.90
Decal, IH Block - "IH" logo, 7 inches printed on vinyl. (Item #: 183292, Ref: R5171) $25.80
Decal, IH Block - "IH" logo, 8 inches printed on vinyl. (Item #: 183123, Ref: R5172) $30.50
Decal, IH Block - "IH" logo, 10 inches. (Item #: 183276, Ref: R5173) $36.60
Decal, IH Block - "IH" logo no background, 1 inch printed on vinyl. (Item #: 183334, Ref: R5174) $2.60
Decal, IH Block - "IH" logo no background, 1-5/8 inches printed on vinyl. (Item #: 183338, Ref: R5175) $3.90
Decal, IH Block - "IH" logo no background, 2 inches x 2-1/2 inch printed on vinyl. (Item #: 183347, Ref: R5176) $5.00
Decal, IH Block - "IH" logo no background, 3 inch x 3-1/2 inch printed on vinyl. (Item #: 183352, Ref: R5177) $14.20
Decal, IH Block - "IH" logo no background, 4-1/2 inch x 4-3/4 inch printed on vinyl. (Item #: 183255, Ref: R5178) $7.50
Decal, IH Block - "IH" logo no background, 5-1/2" x 6" printed on vinyl. (Item #: 183265, Ref: R5179) $16.60
Decal, IH Block - "IH" logo no background, 6-1/2 inch x 7 inch. (Item #: 183547, Ref: R5180) $12.40
Decal, IH Block - "IH" logo no background, 7-1/2 inch x 8 inch. (Item #: 183556, Ref: R5181) $14.80
Decal, IH Block - "IH" logo on silver background, 2 inch x 2-1/4 inch. (Item #: 183560, Ref: R5182) $14.20
Decal, IH Block - "IH" logo no background, 10 inch x 11 inch. (Item #: 183543, Ref: R5183) $25.50
International Decal - 8-1/2 inch long, white with black outline. (Item #: 183068, Ref: R0679) $9.40
International Decal - 23 inches long, black block letters. (Item #: 183477, Ref: R0680) $12.40
International Decal - 23 inches long, white with black outline. (Item #: 183478, Ref: R0681) $16.60
International Decal - 26 inches long, black block letters. (Item #: 183481, Ref: R0682) $14.80
International Decal - 26 inches long, white with black outline. (Item #: 101032, Ref: R0683) $14.00
International Decal - 29 inches long, black block letters. (Item #: 101030, Ref: R0684) $10.50
International Decal - 29 inches long, white with black outline. (Item #: 101033, Ref: R0685) $17.50

Electrical System
NOTE Alternator - Don't see the Alternator you need for your tractor? We have many alternators not listed on this website (for tractors 1953 and newer). Just call us at 800-853-2651.	NOTE
Alternator Conversion Plug - Used to turn Delco SI Style 2-Wire plug alternators into self-exciting style. (Item #: 178026, Ref: ADR9209) $14.40
Alternator Top Adjusting Bracket, Universal - Universal Top Adjusting Bracket for Alternator or Generator is 7/8 inches wide, 1-1/2 inch offset, 8-1/4 inch from farthest end of slot to center of mounting hole, 3-3/4 inch slot length, 3/8 inch mounting hole. (Item #: 173326, Ref: 8NL10302) $25.20
No Picture Alternator, 12 Volt - Universal 63 Amp Delco Alternator. Single wire with built in regulator. Will fit most tractors pre 1980. (Item #: 111377, Ref: 8NE10305SE) $99.00
No Picture Battery Thermal Wrap - 60 Watt, 28 inches long wrap to keep your battery warm. (Item #: BTW28) $35.98
No Picture Battery Thermal Wrap - 160 Watt, 36 inches long wrap to keep your battery warm. (Item #: BTW72) $53.81
No Picture Coil - This universal automotive style coil is 28, 000 volts for a 12 volt system, 2.9 ohms. Measures 6 inches long and 2 1/2 inches diameter. (Item #: 182583, Ref: 28010) $49.20
Distributor Cap, WICO - For All Models with WICO distributor having clip type cap with 3 3/8 inside diameter seat. (Item #: 108299, Ref: X30042) $62.15
Magneto, Wico XH and XHD, Service and Parts Manual - Wico XH And XHD magneto service instructions and parts list. This is a reprint of the original manual that has exploded views of all parts on the tractor with numbered pictures giving great detail on assembly and disassembly. It also gives you a guide with numbers for ordering parts. (Item #: 182504, Ref: MAG6) $19.20
No Picture Spark Plug - Extended tip, 14mm thread, 3/8 inch reach. Replaces Champion J10Y, J11Y, J12Y, J13Y. NOTE: Verify spark plug type before ordering. (Item #: 179437, Ref: AL85) $5.60
Spark Plug - Standard tip, 14mm thread, .472" reach. Replaces Champion L9J, L10, L86, L86C, L88A, L90. NOTE: Verify spark plug type before ordering. (Item #: 182459, Ref: AL425) $4.80
NOTE Starter - Don't see the starter you need for your tractor? We probably have it! Just call us at 800-853-2651 with your make, model, engine cubic inches (CID) and number off your old starter and we will see if we can find it!	NOTE
Starter Solenoid - This is a 3 post, 12 volt Starter Solenoid. Can be used as a saddle mount or flat surface mount. May come in a metal or plastic casing. Replaces: 1114200, 1114207, 1114216, 1114225, 1114235, 1114545, 1114548, 1118820, 1996067, D928, DR1467, DR1485. May come in a silver metal casing versus black plastic. (Item #: 150223, Ref: DR1467) $19.20
Starter, Generator, Distributor Tag, 6 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Item #: 182608, Ref: DELCO6) $16.80
Tag for Starter/Generator, 12 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Item #: 182606, Ref: DELCO12) $16.80
Voltage Regulator, 12 Volt - 4-terminal flat mount. The Three Post side of this regulator may be parallel or slightly splayed. Fits most 12V tractors and combines prior to 1957. (Item #: 105581, Ref: 182548M92) $26.50

Engine Gaskets
Silicone Blue RTV - Permatex ultra blue, no leak RTV silicone gasket, oil resistant, use on valve covers, oil pans, timing covers, water pumps. Temperature range -75 degree F to +500 degree F, 3.35 ounce tube. (Item #: 178141, Ref: PRM77BR) $10.90

Exhaust System
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 118823, Ref: ZNL89020C) $81.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2.5 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119038, Ref: ZNL89025C) $108.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 3.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114858, Ref: ZNL89051C) $132.00
Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.00 inch inside diameter inlet with extended curve. This is a universal part. Verify measurements before ordering. (Item #: 173286, Ref: 146520CHR) $106.00
Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.50 inch inside diameter inlet. It has an extended curve on the outlet. This is a universal part. Verify measurements before ordering. (Item #: 173287, Ref: 146490CHR) $163.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 4.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114945, Ref: ZNL89057C) $147.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 5.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119080, Ref: ZNL89485C) $174.00
Chrome Exhaust Stack - Single Wall, 42 inches long with a slotted, 2.50 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 173281, Ref: L102236CHR) $88.00
Muffler Clamp, 1-1/4 - New Clamp for 1-1/4 inch outside diameter muffler inlet. (Item #: 182682, Ref: MC114) $2.10
Muffler Clamp, 1-3/4 - New Clamp for 1-3/4 inch outside diameter muffler inlet. (Item #: 108866, Ref: MC134) $4.80
Muffler Clamp, 1-3/8 - New Clamp for 1-3/8 inch outside diameter muffler inlet. (Item #: 182687, Ref: MC138) $2.90
Muffler Clamp, 2-1/4 - New Clamp for 2-1/4 inch outside diameter muffler inlet. (Item #: 108870, Ref: MC214) $5.30
Muffler Clamp, 2-3/4 - New Clamp for 2-3/4 inch outside diameter muffler inlet. (Item #: 108872, Ref: MC234) $8.71
Muffler Clamp, 3 - New Clamp for 3 inch outside diameter muffler inlet. (Item #: 108873, Ref: MC300) $7.40
Muffler Clamp, 3-1/2 - New Clamp for 3-1/2 inch outside diameter muffler inlet. (Item #: 108874, Ref: MC312) $8.00
Muffler Clamp, 4 - New Clamp for 4 inch outside diameter muffler inlet. (Item #: 108875, Ref: MC400) $8.30
Muffler Clamp, 5 - New Clamp for 5 inch outside diameter muffler inlet. (Item #: 118841, Ref: MC500) $12.70
Rain Cap - This rain cap is for a 1.750 inch pipe. (Item #: 108632, Ref: R1799) $11.00
Rain Cap - This rain cap is for a 2.0 inch pipe. (Item #: 108633, Ref: R1800) $8.80
Rain Cap - This rain cap is for a 2.50 inch pipe. (Item #: 108635, Ref: R1802) $12.50
Rain Cap - This rain cap is for a 2.750 inch pipe. (Item #: 108636, Ref: R1804) $11.08
Rain Cap - This rain cap is for a 4.0 inch pipe. (Item #: 108645, Ref: R1807) $13.80
Rain Cap - This rain cap is for a 4.50 inch pipe. (Item #: 108749, Ref: WC14) $13.40
Rain Cap - This rain cap is for a 5.0 inch pipe. (Item #: 108750, Ref: WC15) $17.40
Stainless Steel Clamp, 2.75 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 179749, Ref: ZNL90872A) $6.50
Stainless Steel Clamp, 4 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 185428, Ref: ZNL90875A) $8.50

Fuel System / Air Intake
Air Cleaner Filler - Fits many air cleaners that use steel wool type filler. Custom manufactured mesh. 1 bag = 3-1/2 inch x 3-1/4 inch. (Item #: 151026, Ref: S.43231) $14.00
Fuel Tank Screen - This Fuel Tank Screen is used with most stem-type sediment bowls to further protect against debris in the gas line. It has a 0.216 inch Insert Pipe outside diameter - 2.53 inch Overall Length. (Item #: 114940, Ref: R7949) $9.92
Main Fuel Valve - This main fuel valve replaces the original fuel solenoid for International carburetors. The original fuel solenoids are very unreliable and can easily be replaced with this manual valve. This assembly contains: the valve, graphite packing, and packing nut. Used on Carburetors: 50981DC, 45108DB, 50983DC, 52814DA, 47387DC, 361525R92, 358065R92, 362173R92, 367259R92, 380956R91, 380956R92, 380956R93, 381983R91, 381984R95, 389511R92, 367258R92, 396966R91, 388296R91, 388424R96, 396197R96, 396198R92, 381419R91, 397224R93, 381420R91, 357231R91, 356948R92. Replaces 47404DA, 374327R1, 362526R1, 362525R1 (Item #: 117537, Ref: 47404DASSY) $29.80
Sediment Bowl Gasket, 2-1/8 inch - For bowls with 2-1/8 inch diameter, 2.150 inch outside diameter. Made in the USA. (Item #: 112364, Ref: C1778R) $3.30

Gauges
No Picture Amp Gauge - This amp gauge comes with the "IH" logo printed on the face. It has a black face, chrome bezel, and reads 60-0-60. (Item #: 178963, Ref: IHS1837) $30.00
No Picture Hourmeter - DC voltages from 12 volt thru 36 volt nominal. Heavy duty glass-reinforced polyester body. Internal shock shields and grommets protect movement from shock and vibration damage. Fits 2-1/4 inch opening, three (3) mounting screws with nuts and two (2) blade terminals included. (Item #: 178318, Ref: HM771) $63.00
Hourmeter, Analog - 2 inch, black. Can be used on any tractor with a 12 to 24 volt electrical system. (Item #: 178285, Ref: S.52672) $42.30
Oil Gauge - For IHC and Farmall tractors 1947 and and up. Oil Pressure Gauge with color band - Includes mounting bracket. Has IH logo on face. (Item #: 110849, Ref: 41934DB) $49.57
Oil Line Adapter - Oil Gauge fittings may be different even for the same models. Here is an Oil Line Adapter if you have a gauge line without removable fittings, this converts 1/8 inch pipe thread to 1/8 inch tube. Brass. (Item #: 179540, Ref: 919095) $16.00

Hitch / Drawbar
Conversion Tong - Two Point Conversion Tong straight left hand Tong with combination Cat. I and Cat. II Ball. For converting IHC Two Point Fast Hitch to Three Point. About 28 inches overall length. (Item #: 184153, Ref: FH1447) $364.00
Conversion Tong - Two Point Conversion Tong straight right hand Tong with combination Cat. I and Cat. II Ball. For converting IHC Two Point Fast Hitch to Three Point. About 28 inches overall length. (Item #: 184167, Ref: FH1448) $364.00
Conversion Tong - Two Point Conversion Tong bent type, and Cat. II Ball. Left Hand. For converting IHC Two Point Fast Hitch to Three Point. About 32 inches overall length. (Item #: 179611, Ref: FH14416) $439.00
Conversion Tong - Two Point Conversion Tong bent type, right hand Tong with combination Cat. I and Cat. II Ball. Right Hand. The Bent Type spaces out at 32 inches between the ends of the tongs. The Non-Bent Type spaces out at 26 inches between the ends of the tongs. For converting IHC Two Point Fast Hitch to Three Point. About 32 inches overall length. (Item #: 179008, Ref: FH14417) $439.00
Hair Pin Assortment - 15-piece assortment. Includes four (4) of HP-3 (wire diameter 3/16 inch, length 3.75 inch), four (4) of HP-4 (wire diameter 5/32 inch, length 2 15/16 inches), four (4) of HP-5 (wire diameter 1/8 inch, length 2 9/16 inches), and three (3) of HP-6 (wire diameter 3/32 inch, length 1 5/8 inches). (Item #: 182461, Ref: HPA15X) $11.40
Universal Drawbar Lock - For Cat. 1 drawbars up to 1 1/2 inch thick and 3 inches wide. Prevents drawbar from rotating. (Item #: 112156, Ref: DBL2) $37.00

Hydraulic System
Filter Element - 25 Micron replacement element for SF1-25. (Item #: 182541, Ref: 1A9023) $15.40
Filter Element - 10 Micron replacement element for SF1-10. (Item #: 120092, Ref: 1A9021) $13.60
Hydraulic Hose Assembly-NPT, 12 inch - Universal. 12 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118257, Ref: H42-2M-12) $11.00
Hydraulic Hose Assembly-NPT, 180 inch - Universal. 180 inch (15 Feet) overall length. 1/2 inch inside diameter. 2 Wire. Solid Male 1/2 inch NPT thread on both ends. (Item #: 179906, Ref: H42-2M-180) $55.50
Hydraulic Hose Assembly-NPT, 24 inch - Universal. 1/2 inch I.D. double wire braid (SAE-2R) with 1/2 inch NPT solid male fittings both ends. 24 inch overall length. Replaces OEM # - 407435R1. (Item #: 118256, Ref: H42-2M-24) $13.80
Hydraulic Hose Assembly-NPT, 30 inch - Universal. 30 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118259, Ref: H42-2M-30) $16.10
Hydraulic Hose Assembly-NPT, 48 inch - Universal. I.H.C.: 1/2" I.D. double wire braid (SAE-2R) with 1/2" NPT solid male fittings both ends. 48" overall length. Replaces OEM # - 407437R1. Hydraulics: 48 inch overall length (Item #: 118261, Ref: H42-2M-48) $16.50
Universal Pressure Gauge, Hydraulic - 1000 Lb. Gauge. Glycerin Filled. Stainless Steel Case 2-1 2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1 4 NPT male brass fitting. (Item #: 172285, Ref: GG1000) $13.50
Universal Pressure Gauge, Hydraulic - 60lb Gauge. Glycerin Filled. Stainless Steel Case 2-1/2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1/4 NPT male brass fitting. (Item #: 172338, Ref: GG60) $13.40

Implements
Axle Bolt - Axle bolt, 1 each (Ref 3). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36 (Item #: 170217, Ref: BH1317) $14.90
Axle Bolt - Axle bolt, 1 each (Ref 3). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36 (Item #: 170217, Ref: BH1317) $14.90
Bearing Cup - This part fits Caster Assembly (Part Number BH215, Ref #6). Sold individually, two used per caster assembly. Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36. Also replaces 132709, 15191, 32190M1, L44610. (Item #: 169771, Ref: 170BH) $7.86
Bearing cone (L44643) - For Caster Assembly, requires 2.Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 114630, Ref: 22) $5.90
Caster Assembly - Tail wheel and hub assembly with grease fitting and fork assembly. Shaft on Yoke is 1-1/2 inches diameter, 8 inches overall length, 7-1/4 inch to pin hole. New style tail assembly, used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405. Wheel must be attached to fork. For Bush Hog cutters with SPB40 spacer (included), assembly will also replace all models with Timken bearings. (Item #: 173612, Ref: 12269) $183.00
Caster Assembly, Old Style - Tail Wheel and Hub Assembly with grease fitting. 4 x 8 inch rim, 15 inch outside diameter of wheel. Includes wheel, hub, axle bearing and bolt assembly. OLD style tail assembly used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Wheel must be attached to fork. For Bush Hog cutters. With SPB40 spacer, assembly will also replace all models with Timken Bearings (Ref #1-#11). (Item #: 161111, Ref: BH215) $132.00
Hub Assembly - Hub with bushings (3/4 inch), wheel bolts (4), and grease fitting. Center tube length 5 inches. For rotary cutters: RB60 with new style 1-1/4 inch diameter caster, SM60R, SM160R; Squealer models: 1207, SQ36, SQ48, SQ60, SQ72, SQ148, SQ480. Replaces 60978, 60990, 63812. Can use 500BH tail wheel. (Item #: 180514, Ref: 63813BH) $38.10
Hub with Bearing Cups - 4-bolt, 5 inch bolt circle and 3-5/8 inch wheel pivot hub with bearing cups (1 inch axle) (Ref #5). This part fits caster assembly (part number BH215). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36. (Item #: 182627, Ref: BH1311) $49.30
No Picture Round Bale Tine 31.5 Inches - Fully Hardened. Also replaces Kverneland 221151. (Item #: 182589, Ref: 221129) $51.00
No Picture Round Bale Tine 31.5 Inches - Fully Hardened. Also replaces Kverneland 221151. (Item #: 182589, Ref: 221129) $51.00
No Picture Round Bale Tine 38.5 Inches - Fully Hardened. Also replaces Kverneland 241107, 241161. (Item #: 182592, Ref: 241100) $91.48
No Picture Round Bale Tine 43 Inches - Fully Hardened. (Item #: 182594, Ref: 241166) $111.54
No Picture Round Bale Tine 49 Inches - Fully Hardened. (Item #: 152690, Ref: 241162) $78.00
No Picture Round Bale Tine 55 Inches - Fully Hardened. (Item #: 182593, Ref: 241163) $131.61
Seal, Caster - Seal, 2 required (Ref #2). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 180300, Ref: 30BH) $4.30
Tail Wheel Assembly - 4 inch x 8 inch tail wheel assembly with laminated tire. 3-5/8 inch pilot, 4 bolt holes, 5 inch bolt circle, 3-3/4 inches wide, 15 inch outside diameter. Used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405 and 1406, 2510, 2512, 3108, 3209, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Replaces Sidewinder 15205, Servis Rhino 373024H, Terrain King 373024H, Modern 401-0048, BMB 5337, Hardee C40-RC, King Kutter KK4X8. (Item #: 111222, Ref: 500BH) $56.00
No Picture Talc Powder Lubricant - Dry Talc powder lubricant, 8 lb container. Absorbs moisture and keeps treated seed from sticking together in planter boxes. Recommended application rate: 3 oz. Coverage: Typically treats 60-80 acres. (Item #: 107928, Ref: TP19000TP) $22.70

Lights
Headlight Assembly, Teardrop - 6 Volt - Original Style, TEAR-DROP shaped back. PAINTED RED. 6-VOLTS. Approx 5" diameter. Price is for one complete headlamp assembly. Original replacement for many IH tractors. Verify your configuration (Teardrop vs. Flat-Back) before ordering. (Item #: 112415, Ref: 45640DB) $42.80
Headlight Assembly, Teardrop- 12 Volt - Original Style, TEAR-DROP shaped back. PAINTED RED. 12-VOLTS. Approx 5" diameter. Price is for one complete headlamp assembly. Original replacement for many IH tractors. Verify your configuration (Teardrop vs. Flat-Back) before ordering. (Item #: 112414, Ref: 45640DB-12V) $43.10
Light Bulb, Sealed Beam, 6 Volt - 4-1/2 inch number 4511. (Item #: 111227, Ref: 373661R91) $13.50
Portable Halogen Work Lamp - 3 inch x 5 inch sealed beam unit, 12 volt, 50 watt, 4 amp. With handle and magnetic base. Projects flood beam pattern 50 foot wide x 30 foot long. Lamp is not legal for street use. (Item #: L200MAGH) $75.13
No Picture Sealed Beam Light - 6 Volt (Item #: 111938, Ref: R2712) $40.00
No Picture Sealed Beam Light - 12 Volt (Item #: 122080, Ref: R2713) $36.00
Switch, Light, with Knob - Universal switch, for 6 volt tractors. Verify style is correct for your model. (Item #: 114720, Ref: AA4667R) $16.60
Work Light 12V - Universal Work light is 12 volt, 3000 candle power, and a trapezoidal light pattern. I does swivel up and down, not side-to-side. Comes with 4-1/2" diameter sealed beam lamp, part number L4411. Does not have a switch on the back. (Item #: 173803, Ref: L408-12V) $38.40

Miscellaneous
Cab Foam Kit - With Headliner 10-Piece - Black For tractor models with QT1 Year Round Cab. Must be truck shipped - $75 will be added for shipping due to weight and size. (Item #: 186987, Ref: R1236) $389.00
Deluxe Canopy, 3 Bow - This universal Blue 3-Bow Deluxe Canopy comes with bows and cover. Universal brackets sold separately. Fender mounting kit is part number 6A216. Axle Mounting Kit is part number 6A217. Measures about 48 inch spread from Mounting brackets (40 inch spread at the top of canopy) Height is approximately 31 inch. (Item #: 178876, Ref: RFC100B) $245.00
Hand Cleaner, Gallon - Hand cleaner, with dispenser pump. 1 gallon plastic bottle. (Item #: 180453, Ref: PRM25218) $24.60
Tractor Umbrella with Frame & Mounting Bracket - Red - Complete umbrella consisting of a cover, bracket and frame, 54" x 54" cover made of 10 oz. duck canvas with leather reinforcements and steel grommets, Metal parts are zinc-coated for long-lasting, maintenance-free service, Rigid framework for cover is built to withstand farm and industrial use, Installs easily, folds down for trailering and removes in seconds without tools, (Item #: 161193) $123.00

PTO / Driveline
Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor and implement yokes. 1-3/8 inch 6 spline Q.D. tractor yoke. 1-3/8 inch round bore with 1/2 inch pin hole implement yoke. 1300 mm (51 inch) overall length end of yoke to end of yoke. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit, 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch) overall length (43-3/4 inch). Verify length before ordering. (Item #: 180775, Ref: AB4111WY) $174.00
Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor yoke, ratcheting torque limiter on implement end. 1-3/8 inch 6 spline Q.D. tractor yoke, 1-3/8 inch 6 spline ratcheting torque limiter with quick disconnect on implement end. 1372 mm (54 inch) overall length end of yoke to end of clutch. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch). 1372 mm (54 inch) overall length ***VERIFY LENGTH BEFORE ORDERING*** (Item #: 124815, Ref: AB4111K33) $339.00
NOTE PTO Adapter - PTO adapters are located under the PTO category in the Accessories and Universal Parts section.	NOTE
PTO Safety Clutch, 40 HP - 1-3/8 inch 6 spline male and female ends, 6 inch diameter, 40 horse power capacity. Heavy duty unit allows PTO driven implements to freewheel with adjustable safety protection under load. Prevents expensive damage to internal tractor PTO packs. Prevents single clutch tractors from being driven forward by PTO over-run. (Item #: 183648, Ref: B9164) $268.00

Paint
44 Minute DVD - How to Paint a Tractor - This DVD demonstrates the entire painting process including sanding, priming, body work, painting and decals. A John Deere B is used as the sample tractor, but the information will pertain to any make or model - the techniques are the same. Safety is also discussed. (Item #: 183950, Ref: JDV-02250) $24.00
No Picture Paint, Aluminum High Heat Spray Can - 12 oz. spray can. Withstands heat up to 650 degrees for use on stacks and mufflers. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100244, Ref: TP402HHSP_) $8.50
No Picture Paint, Aluminum, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100244, Ref: TP312SP) $8.50
No Picture Paint, Clear Coat, 1 Gallon - High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108409, Ref: TP447GAL) $65.00
No Picture Paint, Clear Coat, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108408, Ref: TP447QT) $29.30
No Picture Paint, Farmall Red, 1 Gallon - This "Farmall" Red is for those models that were manufactured under the earlier FARMALL Brand (Not International). From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101108, Ref: TP110GAL) $55.00
No Picture Paint, Farmall Red, 1 Quart - This "Farmall" Red is for those models that were manufactured under the earlier FARMALL Brand (Not International). From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101107, Ref: TP110QT) $24.60
No Picture Paint, Farmall Red, Spray Can - This "Farmall" Red is for those models that were manufactured under the earlier FARMALL Brand (Not International). From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100720, Ref: TP110SP) $8.50
No Picture Paint, Gloss Black, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100116, Ref: TP550GAL) $53.00
No Picture Paint, Gloss Black, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100115, Ref: TP550QT) $24.00
No Picture Paint, Gloss Black, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100114, Ref: TP550SP) $8.70
No Picture Paint, Gray Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100121, Ref: TP2700QT) $22.40
No Picture Paint, Gray Primer, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Item #: 100120, Ref: TP2700SP) $8.30
No Picture Paint, IH Blue, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101114, Ref: TP910GAL) $58.00
No Picture Paint, IH Blue, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101113, Ref: TP910QT) $24.00
No Picture Paint, IH Blue, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101112, Ref: TP910SP) $8.90
No Picture Paint, IH Red, 1 Gallon - This "IH" Red is for those models that were manufactured under the INTERNATIONAL Brand (Not Farmall). High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100722, Ref: TP905GAL) $56.00
No Picture Paint, IH Red, 1 Quart - This "IH" Red is for those models that were manufactured under the INTERNATIONAL Brand (Not Farmall). High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100721, Ref: TP905QT) $24.00
No Picture Paint, IH Red, Spray Can - This "IH" Red is for those models that were manufactured under the INTERNATIONAL Brand (Not Farmall). High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100720, Ref: TP905SP) $8.50
No Picture Paint, McCormick Deering Gray, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108401, Ref: TP450GAL) $90.00
No Picture Paint, McCormick Deering Gray, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108400, Ref: TP450QT) $35.00
No Picture Paint, McCormick Deering Gray, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108399, Ref: TP450SP) $11.00
No Picture Paint, Off White, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101117, Ref: TP900GAL) $62.00
No Picture Paint, Off White, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101116, Ref: TP900QT) $24.90
No Picture Paint, Off White, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101115, Ref: TP900SP) $8.20
No Picture Paint, Red Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100119, Ref: TP3987GAL) $59.00
No Picture Paint, Red Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100118, Ref: TP3987QT) $24.00
No Picture Paint, Satin Black, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100254, Ref: TP225QT) $24.00
No Picture Paint, Satin Black, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100253, Ref: TP225SP) $8.50
No Picture Paint, Universal Non Glare Black, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100254, Ref: TP120QT) $24.00
No Picture Paint, Universal, Non Glare Black, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100253, Ref: TP120SP) $8.50
No Picture Paint, Yellow Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 184741, Ref: TP2720GAL) $84.67
No Picture Slip Resistant Coating - Gallon can. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116GAL) $68.39
No Picture Slip Resistant Coating Kit - Do it yourself kit. Comes with one gallon of liner, mini roller with tray, two replacement roller covers, 2" brush, and sanding sponge. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116KIT) $99.22
Tire Paint, Black - Black tire paint (1 Gallon)- The best way to make tires look like new. Our paint is a permanent water based paint that applies easily and dries quickly. It will not rub off even when wet. Gives dull, faded tires a non-glossy, like new finish. This paint is READY TO USE. (Item #: 185598, Ref: E844R) $40.01

Seats
Seat, Air Suspension, Black Leatherette, Universal - Seat, Deluxe AG Air suspension, Includes 12 volt compressor. Slides, fore/aft and lateral isolators, adj shock, seat top with Black Leatherette upholstery, lumbar, recline tilt up and angle adjust armrests. *Adjustable backrest recline. *Infinitely adjustable mechanical lumbar support *Heavy duty 12 volt air compressor included. *DOUBLE LOCKING SLIDES, fore and aft isolators with lockout. *Ride firmness adjustment *Weight range 110-330 lbs. *** CALL FOR FREIGHT QUOTE *** (Item #: TS5056V) $1518.86
Seat, Air Suspension, Black Leatherette, Universal - Seat, Deluxe AG Air suspension, Includes 12 volt compressor. Slides, fore/aft and lateral isolators, adj shock, seat top with Black Leatherette upholstery, lumbar, recline tilt up and angle adjust armrests. *Adjustable backrest recline. *Infinitely adjustable mechanical lumbar support *Heavy duty 12 volt air compressor included. *DOUBLE LOCKING SLIDES, fore and aft isolators with lockout. *Ride firmness adjustment *Weight range 110-330 lbs. *** CALL FOR FREIGHT QUOTE *** (Item #: TS5056V) $1518.86
Seat, Air Suspension, Cloth, Universal - Seat, Deluxe AG Air suspension, Includes 12 volt compressor. Slides, fore/aft and lateral isolators, adj shock, seat top with gray cloth upholstery, lumbar, recline tilt up and angle adjust armrests. * Trimmed in FabriForm cloth, can be punctured with pens and screwdrivers and will not tear. *Adjustable backrest recline. *Infinitely adjustable mechanical lumbar support *Heavy duty 12 volt air compressor included. *DOUBLE LOCKING SLIDES, fore and aft isolators with lockout. *Ride firmness adjustment *Weight range 110-330 lbs. *** CALL FOR FREIGHT QUOTE *** (Item #: TS5056) $2161.57
Tie-On Seat Cover - Grey and Red 19". Deluxe cover with 2 inches of foam padding. Does not fit all tractors, must have a pan type seat only. (Item #: 178995, Ref: R2599) $43.80
Tie-On Seat Cover - Red and White, 21" wide. Deluxe with 2 inches of foam. (Item #: 178155, Ref: R1015) $38.60
Universal Seat - Color: Yellow - Universal Application Leatherette Suspension seat. For most Compact, Agricultural and Industrial Tractors. Adjustable base for 5 different mounting angles, Internal Suspension Weight Adjustment, Special Slotted Base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, Adjustable Slide Track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is John Deere Yellow. (Item #: 101375, Ref: TS1040ATSP) $100.00

Sheet Metal / Body Parts
Cab Foam Kit Spray Adhesive - 1 16 Oz. can will attach most kits. Large, multi piece kits may need 2 cans. (Item #: 165963, Ref: R0140) $41.19
Pilot Punch Set - Set contains 12 sizes one of each 1/16, 3/32, 1/8, 5/32, 3/16, 7/32, 1/4, 5/16, 3/8, 7/16 and 1/2. (Item #: 186563, Ref: RPD112K) $173.00

Steering
Eaton Power Steering Pump Replacement - This Power Steering Pump replaces the Eaton style belt driven Power Steering Pump. It also replaces Eaton part numbers: 503-1005-005, 20928 and P761. This is a Redesigned Pump that uses a bearing instead of original bushing. It can also be adapted to tractors using Char-Lynn Power Steering with an Eaton Pump. Please note that this pump does not include brackets, top mounted reservoir, or pulley. Some applications will require a new pressure hose to be made for a 5/8-18 inch inverted flare type fitting. The shaft diameter measures .670 inches. The shaft length, where the pulley mounts measures .575 inches. There is a 2 inch thick pump housing where the bracket bolts on. Pressure is preset at 1.32 GPM. (Item #: 113730, Ref: S03-1003) $417.87
Filter, Power Steering - Filter case size is 3 inches diameter and 1 1/2 inch height. Center hole is approximately 7/8 inch diameter. VERIFY size before ordering. It is used on tractors with Eaton style power steering pumps. Replaces: 133205R91 (Item #: 111126, Ref: AE33538A) $13.20
Power Steering Pump Pulley - This Power Steering Pump Pulley is used with S03-1003 Power Steering Pump. It is designed for Tractors using Eaton Style power steering pump. It is made of Stamped steel. Measures 5 inches outside diameter, 0.675 inch bore, 1/8 inch keyway, 0.9715 inch total width for 1/2 inch belt. (Item #: 164438, Ref: ABC1417) $47.60

Wheels
Front Rim - This is a 6 inches x 16 inches Front Wheel Rim. It has a pilot hole of 4.625 inches. It uses 6 bolts in a 6 inch bolt pattern. Back-spacing is 4.75 inches. Verify size of old rim before ordering. Replaces: 364343R92 (Item #: 103768, Ref: FW60166) $92.00
Front Rim - This is a 5.5 inch x 16 inch Front Wheel Rim. It has a pilot hole of 4.625 inches. It uses 6 bolts in a 6 inch bolt pattern. Back-spacing is 4.75 inches. Capacity of 3500 lbs based on 20 MPH max speed. Verify size of old rim before ordering. (Item #: 116854, Ref: FW55166) $76.00
Tire Inner Tube - This Inner Tube fits 4.00 x 15, 5.00 x 15, 5.90 x 15, 4.50 x 16 and 5.00 x 16 tires. It has a TR-15 valve stem. Valve height 1.38 inch, diameter 0.65 inch. (Item #: 118299, Ref: 500X15TB) $17.15
Tire Paint, Black - Black tire paint (1 Gallon)- The best way to make tires look like new. Our paint is a permanent water based paint that applies easily and dries quickly. It will not rub off even when wet. Gives dull, faded tires a non-glossy, like new finish. This paint is READY TO USE. (Item #: 185598, Ref: E844R) $40.01
Tire Tube - For 5.50 inch, 6.00 inch, or 6.50 inch X 16 inch tires. This is a bias style tube, not for radial tires. Not for recreational use. (Item #: 118295, Ref: WHS050) $19.10
No Picture Tire Tube 24 Inch - This 24 inch tire tube is used for all tractors with the following tires: 10.00 x 24, 11.00 x 24, 11.2 x 24, and 12.4 x 24. (Item #: 178957, Ref: WHS059) $57.00
No Picture Tire Tube 28 Inch - This 28 inch tire tube is used for all tractors with the following tires: 10.00 inch x 28 inch, 11.00 inch x 28 inch, 11.2 inch x 28 inch and 12.4 inch x 28 inch. (Item #: 158249, Ref: WHS058) $63.00
No Picture Tire Tube 28 Inch - This tire tube is used for all tractors with the following tires: 12.00 x 28, 13.00 x 28, 13.6 x 28, and 14.9 x 28. (Item #: 178895, Ref: WHS061) $111.00
No Picture Tire Tube 32 Inch - This 32 inch tire tube is used for all tractors with the following tires: 7.00 inch x 32 inch, 8.00 inch x 32 inch, 9.00 inch x 32 inch and 9.5 inch x 32 inch. (Item #: 184736, Ref: WHS062) $67.00
No Picture Tire Tube 38 Inch - This 38 inch tire tube is used for all tractors with the following tires: 10.00 inch x 38 inch, 11.00 inch x 38 inch, 11.2 inch x 38 inch and 12.4 inch x 38 inch. (Item #: 183819, Ref: WHS064) $82.00
Tire, Three Rib - Front tire, 3 Rib, 5.50 inches x 16 inches. Designed to be used with tube (part number WHS050). 6 Ply. Additional $20 shipping due to size and weight. (Item #: 118213, Ref: 550X16) $107.00
Tire, Three Rib - Front tire, 3 Rib, 5.50 inch x 16 inch. Designed to be used with tube (part number WHS050). 6 Ply. Additional $20 shipping due to size and weight. (Item #: 118213, Ref: 550X16) $107.00
Categories All Super MVTA Parts

Hat
IH Red Hat with Black Brim - With black brim and IH logo. (Item #: 183945) $14.99
IH Solid Red Hat - With IH logo. (Item #: 184041) $14.99
Charcoal Hat with Black Brim - With embroidered Farmall H or M style tractor. (Item #: 140676) $22.99